Denso
Genuine Denso 4D56 Injectors 095000-5600 | Mitsubishi Triton ML, MN 2.5L Standard Output | Standard or +30 | Set of 4
Genuine Denso 4D56 Injectors 095000-5600 | Mitsubishi Triton ML, MN 2.5L Standard Output | Standard or +30 | Set of 4
Taxes excluded. Shipping calculated at checkout.
Couldn't load pickup availability
Genuine Denso 4D56 Injectors 095000-5600 / 260100-4010, Standard Output
Set of 4 | Mitsubishi Triton ML and MN 2.5L 4D56 Standard Output (100 kW), 145 Degree Nozzle | Standard or +30% Modified
Brand new set of four genuine Denso injectors for the standard output 2.5L 4D56 (100 kW / 314 Nm) in the Triton ML and MN. Denso supplies this injector to the aftermarket as 260100-4010, the same injector Mitsubishi fitted at the factory as 095000-5600 (Mitsubishi 1465A041): same body, same 145 degree nozzle, same coding, Denso's own catalogue cross-references the two. The High Power 4D56T in the 4x4 MN and Challenger uses a different injector, and fitting the wrong set on this engine is an expensive mistake. Buy them standard for an OEM replacement, or +30% modified with MCR Performance nozzles for a tuned Triton.
Fitment
| Vehicle | Engine | Build dates | Injector |
|---|---|---|---|
| Mitsubishi Triton ML, MN with the standard output 4D56 (100 kW / 314 Nm), typically 4x2 models | 4D56 2.5L common rail, 145 degree nozzle | approx 07/2006 to 03/2015 | 095000-5600 / 260100-4010 (this set) |
| Mitsubishi Triton MN 4x4, Challenger PB, PC (High Power, 131 kW) | 4D56T HP, 155 degree nozzle | approx 2009 to 2015 | 095000-9560 (1465A257 / 1465A297) |
Quick check: the two 4D56 injectors have different spray angles and do not interchange. Read the number stamped on your injector. 095000-5600 (any -560x revision) or 260100-4010 means this set. 095000-9560 (or -7490, -7491) is the High Power engine and needs the HP set.
Not for the Euro 5 DPF 4D56 (Denso 295050-0890, Mitsubishi 1465A367) or the 3.2L 4M41. Not sure? Add your VIN or State and Rego to the order notes and we will confirm before dispatch. Date ranges are a guide; the stamped number is the source of truth.
Part Numbers and What Arrives in the Box
| Supplied as | 260100-4010 Denso aftermarket part number for this injector. The box and the injector carry 260100-4010, not 095000-5600. |
| Replaces (factory fit) | Denso 095000-5600 and revisions 095000-5601 to -5609 |
| Other Denso references | 9709500-560, DCRI105600 (Denso Europe), box code SM260100-40102F |
| Mitsubishi | 1465A041 |
| Nozzle | 145 degree spray angle (standard output engine), Denso DLLA145P870 |
| Condition | Full engine set of 4, brand new, genuine Denso, compensation code on each injector. Not remanufactured, not exchange, no core deposit. |
Select +30 Modified and we build the same genuine Denso 260100-4010 bodies with MCR Performance +30% nozzles on our bench. Roughly a third more fuel per stroke at the same pulse width, for a Triton going on a remap.
Tune required. The factory map does not know the nozzle changed. Works on the factory turbo with a suitable tune. Built to order, typically 0 to 2 business days, up to 1 to 3 weeks if we are waiting on parts. Bodies still good? 4D56 +30 MCR nozzles only.
Genuine refers to the injector body on a modified set. The nozzle and flow characteristics differ from OEM specification and the flow figure is nominal. Any change to emissions equipment or calibration must comply with the laws that apply to your vehicle and its use.
What Else You Need for the Install
- 4D56 Injector and Rocker Cover Fitting Kit. Seat washers, injector seals and rocker cover gasket. Single-use parts.
Pro tip: never reuse the seat washers. A reused washer is the usual cause of injector rattle and blow-by on a fresh set.
Fitting and Coding Notes
- Enter each injector's compensation code into the ECU in the correct cylinder position with a suitable scan tool, then run the learn procedure.
- Clean the bores and seat faces, fit new seat washers, torque the clamp bolts to Mitsubishi specification.
- Clean-room practice. A single speck of grit in a common rail injector is enough to cause a misfire or a stuck needle.
- Installation by a qualified diesel technician recommended.
Stock and Lead Time
Standard sets are generally in stock and ship same or next business day; if we are between shipments allow 1 to 2 weeks. Modified sets are built to order. On a deadline? Message us before ordering and we will confirm.
Shipping and Payment
- Free insured express shipping Australia wide. Full tracking included.
- Buy now, pay later. Afterpay, Humm, Klarna and Zip.
- International shipping available. Message us for a quote.
Warranty and Fitment Disclaimer
Warranty is covered by our Refund, Returns and Warranty Policy.
It is the customer's responsibility to verify fitment before installation. Rego and VIN checks confirm what the vehicle left the factory with, which may not be correct if the fuel system has been changed.
Frequently Asked Questions
Q: My old injectors say 095000-5600 and the new ones say 260100-4010. Is that the right part?
A: Yes. 260100-4010 is Denso's aftermarket part number for the same injector. Denso supplies 095000-5600 to Mitsubishi for factory fitment and the identical injector to the aftermarket as 260100-4010. Same body, same 145 degree nozzle, coded the same way, cross-referenced in Denso's own catalogue.
Q: Are these genuine or aftermarket?
A: Genuine Denso, brand new, in Denso packaging. Not remanufactured, not exchange, not a copy.
Q: Standard or High Power, how do I tell?
A: Read the injector. 095000-5600 or 260100-4010 is standard output with the 145 degree nozzle. 095000-9560 is the High Power 4D56T with the 155 degree nozzle. Fitting the wrong one causes poor combustion and can damage pistons.
Q: Do these fit the 4x4 MN Triton or the Challenger?
A: No. Those run the 131 kW High Power 4D56T and need the 095000-9560 HP set.
Q: Do the +30 injectors need a tune?
A: Yes. An ECU remap is essential for the modified set. Standard sets need no tune.
Q: Do I need to code them?
A: Yes, standard or modified. Each injector's compensation code must be entered into the ECU, followed by the learn procedure.
Q: Do they come with seat washers?
A: No. Order the 4D56 fitting kit alongside them.
Genuine Denso. Right Spray Angle. Standard or +30.
Set of 4 for the standard output 2.5L 4D56 Triton ML and MN. Free express shipping Australia wide.
Disclaimer: Common Rail Cowboys is not affiliated with Mitsubishi Motors or Denso Corporation. Injectors should be fitted and coded by a competent diesel technician. Fitment and compliance are the buyer's responsibility.
